Skip to main content

Z88 Aurora : Open Source FEA

When reviewing papers for a conference, someone referenced Z88 Aurora (http://www.z88.org) which is an Open Source, cross-platform (Linux, Windows, OSX) Finite Element Analysis software. It is quite extensive and comes with examples and documentation. There is also Z88 (without the Aurora) which is also Open Source. I'm not fully sure about the difference between both... but AFAIK, Aurora contains the more user-friendly GUI with more interactivity, whereas Z88 is more limited in scope.

It contains a pre-processor (load geometry and FEA files, meshing, materials), FE-solver (calculates displacements, stresses and node forces) and a post-processor (visualization of results, export to CSV).

For once, this software is (quite) easy to use on OSX as well, provided you have the X11 system installed, which usually comes with installing the Apple Developers packages, which are included with your OS system disk. It relies on a few external libraries, but even those are embedded or included as a separate download. I had little problem to launch it. But getting something calculated requires more effort ;)

There are even video tutorials included and the read-me PDFs are of quite good quality (even explaining how to configure your trackpad and magic mouse for Mac users).

Screenshot borrowed from Z88 homepage
Edit: after I tested a bit more, I tried to recreate an existing example from another software tutorial to this software, reading alongside with the main userguide, which is quite extensive. Having two screens or at least one large helps a lot (I have a 25 inch + the 15 inch laptop screen).

I started manually defining the nodes (x,y,z), the elements/trusses (from/to node), add a material form the extensive included database, apply the different constraints (fixed nodes, forces) and then run the solver (which was finished before I even noticed something happening). The following screenshot shows onf of the results from the post-processor.

Post-processor results


Comments

  1. Anonymous10 May, 2011

    looks good, have been looking for an opensource FEA...

    keep us posted if get something to calculate.

    regards,

    corneel

    ReplyDelete
  2. I was able to get through an example (see edit in post). Not a clue if it is anywhere close to being realistic (my FEA knowledge is quite dusty), but at least getting through from start to finish is a good first step.

    ReplyDelete
  3. can this z88 aurora open source FEA can simulate welding operation?...which is for example to get the welding displacement??

    ReplyDelete
  4. I don't have a clue. I never even calculated this (unless I was sleeping during our steel-courses) so I wouldn't know how to start.

    But I'd try to look at the documentation. It seems quite open and flexible to do "any" FEA analysis, if I understand it correctly.

    ReplyDelete

Post a Comment

Popular posts from this blog

Improve usage of BIM during early design phases

When I was collecting ideas for a book chapter on BIM (that seemed to never have emerged after that), I collected 10 ideas, which I believe still reflect good recommendations to improve the usage of BIM during the early design phases. These ideas are related to BIM software, but you can apply them in any flavor, as long as you can model with Building Elements, Spaces and have control over representation. Introduction This article gives an overview of several recommendations and tips, to better apply BIM applications and BIM methodologies, in the context of the early design phases. Many of these tips are applicable in any BIM application and they are based on experience gathered from teaching, researching and using BIM software. Sometimes they could help software developers to improve the workflow of their particular BIM implementation. Tip 1 : Gradually increase the amount of information In the early design phases, the architect makes assumptions and lays out the main design in

Getting BIM data into Unity (Part 9 - using IfcConvert)

This is part 9 of a series of posts about getting BIM data into Unity. In this post, we’ll discuss the IfcConvert utility from the IfcOpenShell Open Source IFC Library to preprocess an IFC model for integration with Unity. This is (finally?) again a coding post, with some scripts which are shared to build upon. Conversion of IFC into Unity-friendly formats The strategy with this approach is that you preprocess the IFC-file into more manageable formats for Unity integration. Most Web-platforms do some sort of pre-processing anyway, so what you see in your browsers is almost never an IFC-file, but an optimised Mesh-based geometric representation. However, it wouldn’t be BIM-related if we’d limit ourselves to the geometry, so we will parse the model information as well, albeit using another, pre-processed file. IFC to Wavefront OBJ I used a test IFC-model and used the IfcConvert-utility converted it into OBJ en XML formats. The default way to use it is very simple:

Getting BIM data into Unity (Part 8 - Strategies to tackle IFC)

This is part 8 of a series of posts about getting BIM data into Unity. In this post, we’ll discuss IFC as a transfer format towards Unity. As with the previous post, this is not a coding post, although hints and examples are provided. Open BIM and IFC Everybody who ever met me or heard me present on a conference or BIM-lecture will not be surprised to hear that I’m a strong believer in the Industry Foundation Classes (IFC), an open standard, with already two versions published as an ISO standard, being IFC2x2 and IFC4 (but surprisingly not IFC2x3 which is widely used). In the ideal world, this would be the format to use to transfer BIM data into another environment, such as Unity. So what are our options? Looking in the Unity Asset Store Assimp is a library which supports multiple formats, including IFC. https://assetstore.unity.com/packages/tools/modeling/trilib-unity-model-loader-package-91777   I did a few attempts, but alas without any success. It is possib